玉米淀粉基降解環保餐盒，是采用玉米淀粉及植物纖維為基料，輔之以生物聚酯、多元醇等物質加工而成，其淀粉含量高可達80，在土壤和自然環境下可以自然降解，對環境沒有污染、無破害。那么您知道玉米淀粉顆粒可降解餐盒成型遇到問題有哪些嗎？

The corn starch based degradable environment-friendly lunch box is made of corn starch and plant fiber as the base materials, supplemented by biological polyester, polyols and other materials. Its starch content can reach 80, which can be naturally degraded in soil and natural environment, without pollution and damage to the environment. Do you know the problems encountered in the molding of corn starch granules degradable lunch boxes?

①片材加熱時間太短或加熱器溫度太低,應適當延長加熱時間或提高加熱管溫度

① If the heating time of the sheet is too short or the temperature of the heater is too low, the heating time should be appropriately extended or the temperature of the heating tube should be increased

②加熱器加熱功率偏小.應適當加大加熱器的加熱功率

② The heating power of the heater is too small. The heating power of the heater should be increased appropriately

③片材受熱不均勻,成型缺陷總是在同一部位重復的出現.應用熱屏蔽網調節片材的受熱狀態,使各部位均勻受熱

③ The heating of the sheet is uneven, and the forming defects always appear repeatedly at the same part. The heat shielding net is used to adjust the heating state of the sheet, so that all parts are heated evenly

④夾片前夾持架沒有預熱,夾片前應預熱夾持架；

④ The clamping frame in front of the clip is not preheated, and the clamping frame shall be preheated in front of the clip;

⑤真空孔阻塞,真空度偏低.應清理和梳理真空孔

⑤ The vacuum hole is blocked and the vacuum degree is low. The vacuum hole should be cleaned and combed

⑥真空孔數量太少或孔徑太小,真空度偏低.應適當增加真空孔或加大真空孔孔徑,如有可能,可用真空窄縫代替真空孔

⑥ The number of vacuum holes is too small or the hole diameter is too small, so the vacuum degree is low. The vacuum holes or the hole diameter of vacuum holes should be increased appropriately. If possible, the vacuum holes can be replaced by vacuum narrow slots

⑦真空罐或真空泵的容量太小,真空牽引力不夠,應適當增加真空罐或真空泵的容量,加大真空管閥件,在三通和彎管處避免急彎

⑦ The capacity of the vacuum tank or vacuum pump is too small, and the vacuum traction force is not enough. The capacity of the vacuum tank or vacuum pump should be increased appropriately, the vacuum pipe valves should be increased, and sharp bends should be avoided at tees and elbows

⑧氣壓成型的壓力不足.應在模具結構條件允許的情況下,采用137——206Pa的氣壓,也可使用框架助推器或柱塞助壓

⑧ The pressure of pneumatic forming is insufficient The air pressure of 137-206Pa shall be used, or the frame booster or plunger can be used, if the mold structure conditions permit

玉米淀粉可降解餐盒的前景成型過程中遇到的問題就是以上所講解的這些了，您可以作為參考信息來看看，當然您在操作時需要正規專注的技術人員做協助。關注我們http://tecnoleo.com了解更多事項！

The problems encountered in the future molding process of corn starch degradable lunch boxes are those described above. You can take a look at them as reference information. Of course, you need the assistance of regular and dedicated technicians when operating. Follow us http://tecnoleo.com Learn more!